Therma-Tru Window Installation Nationwide | Winslow Windows & Doors

Therma-Tru Window Installation: The Gladeview Owner’s Guide

Therma-Tru window installation in Gladeview typically runs $320 to $680 per window for a full retrofit, including removal of the old unit, flashing, insulation, and trim work. We stock Therma-Tru-compatible installation kits and hardware on our trucks, so most Gladeview jobs are completed the same day we show up. The way homeowners usually find us is simple: the window starts sticking on humid mornings, a corner shows daylight, or water stains appear along the sill after a hard rain and they realize the original install wasn’t done right. We’re an independent service provider, not affiliated with Therma-Tru, but Ed Winslow has been fitting these windows in South Florida long enough to know exactly what a bad installation looks like from the inside out.

Call (727) 604-9322

Which Therma-Tru Models This Applies To

Our Therma-Tru installation work covers the full residential window line you’ll find in Gladeview homes: the double-hung, single-hung, casement, awning, sliding, and picture windows, including the Classic-Craft and Smooth-Star series that pop up constantly in the neighborhoods off NW 22nd Avenue. Here’s the gotcha most owners don’t know: Therma-Tru uses different frame depths depending on whether the window was ordered for new construction or retrofit, and the installation method changes completely between those two. If you pull the interior trim and measure the jamb depth, you can usually tell us over the phone which setup you have. Generally, that’s 3-1/4 inches for standard retrofit frames and 4-9/16 inches or deeper for new-construction units built into stucco openings.

For Gladeview homeowners, we recommend OEM Therma-Tru installation hardware when your windows are still under warranty, because aftermarket flashing and receiver blocks can void the coverage if Therma-Tru’s inspector gets picky. Once the warranty period is done, a quality aftermarket installation system from brands like OSI or Protecto Wrap does the same job at roughly half the kit cost. We’ll walk you through the tradeoff honestly before you spend a dime.

Signs Your Therma-Tru Window Installation Is Failing

• Condensation trapped between the panes. This means the seal around the insulated glass unit has failed, and in Gladeview’s humidity, that fog becomes permanent within weeks. The installation itself may be sound, but the window unit likely needs replacement.
• Daylight visible at the corners of the frame. The window was probably shimmed wrong or the rough opening wasn’t square when the original installer set it. This is a flashing and insulation failure waiting to happen, and in Gladeview’s wet season, it becomes a rot problem fast.
• The sash sticks or won’t lock cleanly. We see this constantly in older stucco homes along the Palmetto Expressway corridor, where heat and moisture cycles cause the opening to shift. The installation wasn’t adjusted for movement tolerance, and the frame is now binding.
• Water stains on interior drywall below the window. That’s not a window feature, it’s a flashing failure. Water is getting behind the exterior finish and running down inside the wall cavity, which in Gladeview’s climate means mold follows quickly.
• Drafts you can feel with the window closed and locked. The weatherstripping may be fine, but if the rough opening wasn’t insulated or sealed properly during installation, air moves around the frame, not through the sash. Your AC bill shows it every August.

Replacement Cost & What’s Included

For Gladeview homes, a full Therma-Tru window installation with us runs $320 to $680 per window. The range depends on three things: whether the existing rough opening needs repair before we set the new frame, what depth your current window was installed at, and whether we’re working on a second-story opening that needs a lift. Here’s what you get with that number:

• Removal and disposal of the old window and hardware
• Rough opening inspection and minor repair
• New flashing system, insulation, and sealant rated for South Florida exposure
• Precise shimming and leveling of the new Therma-Tru window
• Interior and exterior trim that matches your existing profile
• A written line-item quote before any work starts, with no change orders

Every installation carries our workmanship warranty and the Done Right Promise. If it’s not done right, we come back and make it right. Period.

DIY or Call Us?

You can safely inspect a failing Therma-Tru window yourself: check for daylight at the corners, feel for drafts on windy days, and look for water-stained drywall below the sill. But here’s where DIY goes wrong, and we’ve seen the aftermath in Gladeview more times than we can count. A stucco exterior means once you pull a window out, you’ve committed to repairing the opening, flashing it correctly for hurricane season, and resealing the stucco system. If you get the flashing wrong by half an inch, water intrusion shows up months later as rot inside the wall. And in a coastal climate like ours, a compromised wall cavity becomes a structural problem, not a cosmetic one. For homeowners who’d rather not face that risk, call (727) 604-9322 and we’ll take it from there.

FAQs